AmTech Round Tail 1/48 scale
P-40K-5 Warhawk

by Floyd S. Werner Jr.

HyperScale is proudly supported by Squadron.com

History

The heaviest of the P-40 family the P-40K came in three variations.  The first looked exactly like the P-40E.  This was followed by the K-5 version, which has the characteristic large rounded tail section.  To add to the confusion, this tail could also be retrofitted to the P-40E.  The final version of the K had the extended tail like the P-40F.  How the Curtiss and field units ever kept track of what parts were interchangeable is beyond me.  Originally designed as an intermediate aircraft the P-40K was produced in great numbers with most of the aircraft being in North Africa, Pacific and in China. 

For those interested here is a link to my P-40F article: http://hsfeatures.com/features04/p40fwarhawkfw_1.htm . Obviously many of the features and techniques mentioned in the earlier article are the same as the P-40F so I will not go into detail unless something is different.

The Kit 

The contents of the kit are the AMtech P-40E kit, including the replacement fuselage, a tan resin tail and set of colorful decals for three airplanes.  The instructions are clear and concise on where and when to cut the old tail off.  The instructions have you place the fuselage on the instructions and cut off the tail. 

The downside to this kit is that it currently a very limited availability kit being marketed through Hobby Lobby in the US only. 

Box artwork by Jerry Boucher shows one of the decal options to great detail.  The resin tail is cast by Black Box and is beautifully detailed.

Cutting Edge Cockpit 

The kit cockpit is actually very nice, but I had a Cutting Edge set that was beautiful so I just had to use it.  The fit was perfect.  The construction is very straightforward and presented no problems whatsoever.  I preshaded the cockpit with flat black and then used Humbrol Bronze Green.  A wash of Burnt Umber in the recesses accentuated the shadows. 

I dry brushed the cockpit with zinc chromate and highlighted the worn areas with a dry brushed with some silver.  Some color of Apple Barrel acrylic paint was used on some for detail painting.  Finally, some touches of a silver pencil made the whole thing come to an end. 

Wings 

Nothing different from the P-40F except that I removed the guns and replaced them with hypodermic needles.

Fuselage and Tail Conversion 

Prior to adding the tail, I recommend that you clean out the excess resin from the rudder hinge line.  It is very thin and easy enough to do.  This allows the see through effect so prominent on the K. 

The instructions provide you with a drawing, which you then lay, the fuselage halves over. Then you cut the tail off.  I must admit that I cut my first set of fuselage halves too short.  You receive two fuselage halves per side, so I got another shot at it.  I cut long and sanded it flush with a BAF (Big Ass File).  I then followed the instructions and had no problem with the fit.  I used Superglue and accelerator to set the resin tail in place.  The superglue filled any seam.  I then sanded it smooth and had to rescribe any panel lines, but they were no big deal as they were all straight lines.  The horizontal tail planes fit great to the resin tail. 

The rest of the construction went great with no real problems encountered anywhere.  The only thing I did do that differed from the normal construction was cut an index card to fit into the openings for the back of the engine and the inlet on top of the engine.  These were colored with black marker and they only served to prevent a see through effect. 

I’ll let you in on a little hint.  The prop spinner does not have a panel line.  The panel line can be easily scribed with a straight pin held in a pin vise.  This is then elevated with post it note pads to the proper height, hold it tightly in place and spin the spinner.  This ensures that the line is straight and the same height throughout.

Painting

I used Black Magic CEBM48336 for the P-40K canopy.  These fit perfectly and simplified a job I hate.  They stick perfectly and prevented any bleed.  Highly recommended.

I used Polly-S US Khaki for the tan.  I used Black Magic camouflage masks (CEBM48153), which are actually designed for the P-40B/C but easily modified for the complex painting.  After the masks were laid down I used Gunze Dark Green for the top camouflage colors.  Model Master Enamel RLM 63 substituted for the bottom side.  I liked the tonal qualities of these colors.

Cutting Edge Decals 

Once dry, a coat of Tamiya Clear from the spray can prepared the surfaces for decals.  The kit decals are very nice, but I wanted to do something a little different.  I used the Cutting Edge Decal sheet CED48171 P-40 Warhawk Part 3.  It contained a large sharkmouth for “Old Hellion” from the 18^th FS in China.  The decals reacted well with MicroSol and MicorSet.  For the sharkmouth I decided on Solvaset because of the complex curves.  I caused the only problems experienced.  I touched up the offending area with Apple Barrel paints.  The decals were sealed with another gloss coat of Tamiya spray gloss and then a coat of Model Master Acrylic Flat.

Weathering 

Weathering is done in layers.  First chip the paint with silver pencils, pens, and a dry brush of silver paint.  Particular attention is paid to the high traffic areas.  Next, I like to use Burnt Umber artist oils on all the panel lines.  While I'm doing that I also "streak" oil stains. 

Next I like to add the gun stains with pastels.  I think pastels give me more control for this area.  I start the exhausts with Tamiya Flat Black heavily thinned.  This was built up slowly.  Once happy with the results I used a Model Master Grey and applied it in irregular patterns.  The P-40 has a distinct way the exhaust streaks because of rain and handling.  I took a long soft bristle brush and lightly dipped it in Turpenoid.  I then took the almost dry brush over the grey in a vertical pattern.  I was very happy with the exhausts.  I then took a very thin coat of Tamiya Buff and sprayed streaks from front to back on the wings and top to bottom on the fuselage.  Everything was sealed with another coat of Model Master Acrylic Flat.   

The new P-40K is more accurate than the previous offering by AMT/Ertl.  Because of this it is the best available P-40K on the market.  Some will ask if the tail will fit the Hasegawa kit, yes it will fit.  A little sanding will allow for the resin tail to be inserted in the Hasegawa kit.  If I had to find something wrong with the AMtech P-40K, I would say that the limited availability is my biggest beef.  Ask your people from the South to look for them at the local Hobby Lobby.  You may be able to order them online as well.  While comparisons between the Hasegawa and AMtech are inevitable, I think this kit from AMtech is up for the match.   The detail is not quite as good and the plastic is a little soft, but when built it looks every bit the P-40.  You don’t have to fill all those plugs in the Hasegawa kit.  I wouldn’t sell off my AMtech kit to get the Hasegawa, but if you do, I will be there scarfing them up.  My hat is off to AMTech for making the most of their molds.  I highly recommend this kit to everyone but the beginner modeler.   

I'd like to thank AMTech for the review example. 

• World War 2 US Army Fighter Modeling, Jerry Scutts & Brett Green, Osprey Publishing, 2003, ISBN 1-84176-061-7

• P-40 Warhawk Walk Around #8, Lou Drendel, Squadron/Signal Publications, 1996, ISBN 0-89747-361-2  

• Curtiss P-40 in action, Ernest R. McDowell, Squadron/Signal Publications, 1976, ISBN 0-89747-025-7 

• P-40 Warhawk in detail, Bert Kinzey, Squadron/Signal Publications, 1999, ISBN 1-888974-15-X 

• P-40 Warhawk in World War II Color, Jeffrey L. Ethell, Motorbooks International, 1994, ISBN 0-87938-928-1

Click the thumbnails below to view the images full-sized.
Use your browser's Back Arrow to return to this page:

Modelling the P-40 Hawk 81, Tomahawk, Warhawk and Kittyhawk Osprey Modelling 15 Author: Brett Green US Price: $17.95 UK Price: £12.99 Publisher: Osprey Publishing Publish Date:  January 10, 2004 Details: 80 pages; ISBN: 1841768235 Shop Buy it from Osprey Publishing

Model, Images and Text Copyright © 2005 by Floyd S. Werner Jr.
Page Created 07 August, 2005
Last Updated 06 August, 2005

Back to HyperScale Main Page